Factory Reset Codes

Repair forum for T.V's and Monitors only.

Factory Reset Codes

Postby D4Rk » Thu Feb 13, 2014 1:34 am

**** WARNING!!!! ******

Some of these procedures may allow you to enter factory service modes. IF YOU DO NOT KNOW WHAT YOU ARE DOING, DO NOT MAKE CHANGES TO SETTINGS IN FACTORY MODES!! Improper settings may cause undesired operation, and could result in a situation where your TV cannot boot/turn on.

YOU ARE USING THESE PROCEDURES AT YOUR OWN RISK!!


Factory Resets / modes

For all listed procedures, start with TV on, in TV mode, unless otherwise instructed. After procedure is complete, unplug set and re-plug in to finish reset.

If more than one procedure is listed for a given manufacturer, try the different ones until you see which one works for your set.

Coby:****************************************-

Enter menu, hi-lite “audio” then enter 8893

mode/source 2580 select “other setting”,select “shipment” then yes, after it exits service menu you need to power set off.



Dynex ****************************************-

source/input 2580

hold vol down on tv and hold #1 button on remote, vol will jump to halfway and set shuts off. Turn back on have 1st time setup screen.

source/input 2580

menu 1999 (tv is on)



Element ****************************************

menu 0000

menu 1147


Haier ******************************************

pull up menu, hi-lite “audio” then enter 8893




Hisense *****************************************

In customer menu go to”Parental” enter 0000 then select”Clean All” then power the set off and back on and first time setup menu will be there.

For some models, same as above model except in menu it is labeled “Lock”



Insignia *****************************************-

input 2580 (tv is on)



Mitsubishi ****************************************

Menu 123 or menu 2470 (tv is on)



Panasonic

Hold vol- on TV, press and hold menu button on remote



Philips ******************************************

Push menu, select”Features”then select”current software info” push 062596-info on remote then push info again then red”initialize appears and changes color then complete. Push power button to exit

TV is on,push 062596-info on remote,then push info again, red”initialized”appears it turns green when completed, then push power button to exit

Polariod *****************************************-

Hold vol- and chan- or hold vol+ and chan+ (tv is on)



Proscan ******************************************

In customer menu go to setup,select parental control menu, enter 0000 then select “clear channel list”.



RCA *******************************************-

Menu 1147



Sanyo *******************************************

hold vol down on TV, press and hold #1 button on remote, vol will jump to halfway and set shuts off. Turn back on have 1st time setup screen.



Samsung *****************************************-

Mute 182 power (tv is off)
(On some models, Factory Reset is on this menu, on some, you must go into the “Options” submenu



Seiki ********************************************-

Menu 0000



Sharp ********************************************
(Note – On Sharp models, you will need to look through the menus to find the reset option)

menu 1999

menu, 3481

menu 1147

while holding vol– & input buttons on tv plug in set when “k” appears push vol– & chan-



Sony *********************************************

Hold “arrow up” on remote and push power button on tv (tv is on)




Symphony *****************************************-

Source/input 2580




Toshiba ******************************************-

on Menu, select “Installation”, then “System Information” press the right arrow button, (“System Information” will change to “Factory Reset” or something similar) follow on-screen instructions



Vision Quest ***************************************-
Source/input 2580



Vizio ********************************************

In customer menu under “Help” tab is Factory Default enter 0000


Vestel (most):
Menu 4725 then select "RESET"

Samsung (European):
Power off, Info - Menu - Mute - Power, then find factory reset and execute option.

LG/Zenith:
Hold MENU on TV and MENU on remote for 5~10 seconds, then select reset option.

NEC:
While powering on hold "MENU" or "INPUT" on TV, depending on model. (Only disables error lock out/buffer and puts TV in temporary service mode.)
To reset to factory, on remote, Off Timer - Menu - Exit - Off Timer, then select reset option.

Props to randtek @badcapsnet for this information.

Please feel free to add to this list if you have have any information.
Thanks!
User avatar
D4Rk
VIP Member
VIP Member
 
Posts: 828
Joined: Fri Oct 19, 2012 10:15 pm
Location: Usa
National Flag:
United States of America
Has thanked: 93 times
Been thanked: 144 times
Set up: My hands

Factory Reset Codes

Sponsor

Sponsor
 

Return to T.V's and Monitors

Who is online

Users browsing this forum: No registered users and 1 guest

cron