DIY Heat Gun Top Heater with DIY Nozzle

Forum for all DIY topics.

Re: DIY Heat Gun Top Heater with DIY Nozzle

Postby aisikterix » Fri Nov 27, 2015 11:21 am

code0102stinks wrote:
moddzy wrote:Who made the hot air gun part? Aoyue?


No, it's a very cheap heat gun you buy at any hardware store.


How many watts is the heater? Can I use the handle of the 958 GORDAK?it has a built-in fan. It remains to be connected to the controller of the air flow
Image
aisikterix
Valued Member
Valued Member
Progress to next rank:
10%
 
Posts: 31
Joined: Tue Mar 19, 2013 1:35 pm
Location: Bulgaria
National Flag:
Bulgaria
Has thanked: 6 times
Been thanked: 2 times
Set up: ya xun

Re: DIY Heat Gun Top Heater with DIY Nozzle

Sponsor

Sponsor
 

Re: DIY Heat Gun Top Heater with DIY Nozzle

Postby code0102stinks » Sat Nov 28, 2015 6:13 pm

My DIY heat gun element is about 1300W stock, but I use a power diode as a half wave rectifier to cut the wattage in half to about 650W.
I looked up the spec on your Gordak and it is only rated at 300W and that would be pretty wimpy to be trying to spread the heat out to
heat a large bga chip like a GPU.
code0102stinks
VIP Member
VIP Member
 
Posts: 688
Joined: Sun Dec 09, 2012 5:18 pm
Location: WA, US
National Flag:
United States of America
Has thanked: 78 times
Been thanked: 232 times
Set up: DIY Hot Air Top Heater and Nozzle. Modded T8280 Preheater

Re: DIY Heat Gun Top Heater with DIY Nozzle

Postby aisikterix » Sat Dec 19, 2015 9:10 pm

I wanted to experiment with these things here:
1. Handle heater 300 watts, 958 GORDAK small turbine with integrated 24 Volt
3. Stabilized rectifier 24 volts.
4. step regulator of speed turbines.
The heater is connected to it in the manner which was connected an infrared heater. Can not run the profile. "SV". flashes on the temperature controller and can not surpass 80 degrees. can not continue profile . thermo controller is ALtec P410.Probe touching video chip. Display "PV" temperature greater than 80 degrees.What is wrong?
Excuse me for bad English.

Image
Image
Image
Image
aisikterix
Valued Member
Valued Member
Progress to next rank:
10%
 
Posts: 31
Joined: Tue Mar 19, 2013 1:35 pm
Location: Bulgaria
National Flag:
Bulgaria
Has thanked: 6 times
Been thanked: 2 times
Set up: ya xun

Re: DIY Heat Gun Top Heater with DIY Nozzle

Postby code0102stinks » Sun Dec 20, 2015 5:02 pm

I assume you are 220v where you live? Do you have 220v powering heating element of hot air wand? If you did a video
showing it hooked up and running it would help.
code0102stinks
VIP Member
VIP Member
 
Posts: 688
Joined: Sun Dec 09, 2012 5:18 pm
Location: WA, US
National Flag:
United States of America
Has thanked: 78 times
Been thanked: 232 times
Set up: DIY Hot Air Top Heater and Nozzle. Modded T8280 Preheater

Re: DIY Heat Gun Top Heater with DIY Nozzle

Postby aisikterix » Sun Dec 20, 2015 8:21 pm

heater voltage is 220 volts. only the turbine is 24 volts. the heater is controlled by Altec P410 by SSR.air flow is controlled by a stepper controller. I Will make video to see what happens.
aisikterix
Valued Member
Valued Member
Progress to next rank:
10%
 
Posts: 31
Joined: Tue Mar 19, 2013 1:35 pm
Location: Bulgaria
National Flag:
Bulgaria
Has thanked: 6 times
Been thanked: 2 times
Set up: ya xun

Re: DIY Heat Gun Top Heater with DIY Nozzle

Postby aisikterix » Sun Feb 07, 2016 9:46 am

I have a question to my colleague 'code0102stinks " . What is the wire that connects the omega plug with pc410 .Here this Image
Image
aisikterix
Valued Member
Valued Member
Progress to next rank:
10%
 
Posts: 31
Joined: Tue Mar 19, 2013 1:35 pm
Location: Bulgaria
National Flag:
Bulgaria
Has thanked: 6 times
Been thanked: 2 times
Set up: ya xun

Re: DIY Heat Gun Top Heater with DIY Nozzle

Postby code0102stinks » Sun Feb 07, 2016 3:51 pm

aisikterix wrote:I have a question to my colleague 'code0102stinks " . What is the wire that connects the omega plug with pc410 .Here this Image
[ Image ]


It is just a chunk of wire I cut from a bad type K TC and used it as type K TC carrier wire for TC plug to PC410 input.
code0102stinks
VIP Member
VIP Member
 
Posts: 688
Joined: Sun Dec 09, 2012 5:18 pm
Location: WA, US
National Flag:
United States of America
Has thanked: 78 times
Been thanked: 232 times
Set up: DIY Hot Air Top Heater and Nozzle. Modded T8280 Preheater

Re: DIY Heat Gun Top Heater with DIY Nozzle

Postby aisikterix » Mon Feb 08, 2016 7:46 pm

thank you very much :thankyou:
aisikterix
Valued Member
Valued Member
Progress to next rank:
10%
 
Posts: 31
Joined: Tue Mar 19, 2013 1:35 pm
Location: Bulgaria
National Flag:
Bulgaria
Has thanked: 6 times
Been thanked: 2 times
Set up: ya xun

Re: DIY Heat Gun Top Heater with DIY Nozzle

Postby crossleymarko » Sat Mar 26, 2016 1:13 am

any progress on this
:ugeek: :ugeek: :ugeek:
crossleymarko
Valued Member
Valued Member
Progress to next rank:
30%
 
Posts: 33
Joined: Fri Aug 29, 2014 9:01 pm
Location: leigh
Has thanked: 6 times
Been thanked: 4 times
Set up: wATS IT TO YOU.. ILL TELL YA AFTER

Previous

Return to DIY Forum

Who is online

Users browsing this forum: No registered users and 1 guest

cron