Guide to correctly setting a reball jig (ht90 and similar)

Place your before and after pictures here and any repair tips you may have .Remember no Rgh/Jtag work.

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby wills123 » Fri Jul 27, 2012 7:28 pm

not if u drill holes just big enough for allen key to go trhough, as the grub screws are slightly bigger than the allen key itself, however your method works fine also 8-)
wills123
VIP Member
VIP Member
 
Posts: 2997
Joined: Wed Jun 20, 2012 8:44 pm
Location: kingslynn,norfolk
National Flag:
Great Britain
Has thanked: 573 times
Been thanked: 422 times
Set up: highly modded achi ir6000,2400w switched bottom,omega tc port,internal vac pump

Re: Guide to correctly setting a reball jig (ht90 and simila

Sponsor

Sponsor
 

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby CRW » Fri Jul 27, 2012 7:35 pm

true pal.
CRW
VIP Member
VIP Member
 
Posts: 256
Joined: Sun Jun 17, 2012 5:29 pm
Location: accrington, lancashire
Has thanked: 0 time
Been thanked: 8 times
Set up: hr360, honton 1212, aoyue 937, wep 898bd and loads more i cant fit on.

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby Wolf » Sat Jul 28, 2012 5:30 am

Believe it or not I never knew you had to level these things, I just assumed that it was what it was as far as the stencil being flat..gonna give it a shot next time I ball a 360 southbridge since right now the balls fall through the stencil and roll around on the chip..everything else is fine but that one..
Wolf
Banned
Banned
 
Posts: 235
Joined: Mon Jun 18, 2012 1:36 am
Location: USA
National Flag:
United States of America
Has thanked: 6 times
Been thanked: 32 times
Set up: Scotle IR6000 V4

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby Telboy » Sat Jan 19, 2013 11:26 am

On you 'TIP' you use 'insat', so I have lookedup insat and find several products:

    INSAT VOC FREE NO-CLEAN ROL0 LIQUID FLUX
    INSAT SUPER FLUX ..... etc

could you please tell me what is the whole name of the insat that your refering to.

Thanks
Telboy
New Member
New Member
Progress to next rank:
40%
 
Posts: 2
Joined: Sat Jan 19, 2013 10:01 am
Has thanked: 0 time
Been thanked: 0 time
Set up: BK 7050 and HotGun2

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby Flashing360 » Sat Jan 19, 2013 11:35 am

Insat super flux
Flashing360
 

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby Telboy » Sun Jan 20, 2013 10:21 am

Thanks.
Telboy
New Member
New Member
Progress to next rank:
40%
 
Posts: 2
Joined: Sat Jan 19, 2013 10:01 am
Has thanked: 0 time
Been thanked: 0 time
Set up: BK 7050 and HotGun2

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby martinjj » Mon Mar 18, 2013 4:04 pm

Brilliant piece of info, i was just googling for this exact information, many thanks
martinjj
Valued Member
Valued Member
Progress to next rank:
60%
 
Posts: 28
Joined: Thu Mar 14, 2013 2:13 pm
Location: Rotherham, South Yorks. Its a pimple on the arse of the world
National Flag:
Great Britain
Has thanked: 5 times
Been thanked: 16 times
Set up: Aoyue 968 and puhui t8280, hoping to progress to higher things

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby karlmiles » Wed Mar 20, 2013 8:37 pm

How can i raise the chip on this? The adjusting screws are all flat. The gap between the chip and the stencil are too far apart.
Karl
You do not have the required permissions to view the files attached to this post.
karlmiles
Elite Member
Elite Member
Progress to next rank:
50%
 
Posts: 75
Joined: Wed Nov 28, 2012 8:46 pm
Location: East Yorkshire.
Has thanked: 0 time
Been thanked: 0 time
Set up: Achi IR6500. Omega TC

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby Flashing360 » Wed Mar 20, 2013 10:02 pm

that pic is so small i cant see a thing mate, how have you got the chip placed in the vice?
Flashing360
 

Re: Guide to correctly setting a reball jig (ht90 and simila

Postby jfl14609 » Sun Aug 18, 2013 11:24 pm

I just want to say thank you to Marko for pointing me to this thread and of course fersy for making it but I cant stress enough if your new to reballing follow this. I fought for hours then read this thread on what now seems elemental and I cann reball a xbox in like 15 mins
jfl14609
VIP Member
VIP Member
 
Posts: 306
Joined: Mon Feb 25, 2013 4:01 pm
Has thanked: 6 times
Been thanked: 10 times

PreviousNext

Return to Showcase Your Repairs, Tips & Tricks

Who is online

Users browsing this forum: No registered users and 1 guest

cron