Scotle IR 360 pro V3 Bottom IR heaters don't turn on..

Support forum for Scotle BGA rework stations.

Re: Scotle IR 360 pro V3 Bottom IR heaters don't turn on..

Postby code0102stinks » Tue May 12, 2015 1:15 pm

On each SSR, there are term 1 & 2 for the high AC voltage side. One of those will have 220v with machine main power on, the other goes to
whatever heating element it controls. If the red LED on that SSR is lit, then the circuit between term 1 & 2 will be completed. Did you follow
wires from plates to SSR to identify which SSR is for lower preheater plates? Use your DVOM and see if both term 1 & 2 have 220v when LED is
lit. If both have 220 and plates not heating, then put make sure plates have connection on the Neutral side.
code0102stinks
VIP Member
VIP Member
 
Posts: 707
Joined: Sun Dec 09, 2012 5:18 pm
Location: WA, US
National Flag:
United States of America
Has thanked: 78 times
Been thanked: 234 times
Set up: DIY Hot Air Top Heater and Nozzle. Modded T8280 Preheater

Re: Scotle IR 360 pro V3 Bottom IR heaters don't turn on..

Sponsor

Sponsor
 

Re: Scotle IR 360 pro V3 Bottom IR heaters don't turn on..

Postby BGA_netherlands » Sat May 23, 2015 8:13 pm

I find out one SSR is broken. I have a honton hotplate and it have the same SSR. So i tried all 3 SSR's from the IR 360 in the honton hotplate. And 1 SSR is broken.

Then i have switched the broken SSR with the top heater SSR and now the upper heater won't work. So i'm sure this SSR is broken. But with the SSR from top heater installed on the bottom heater it must work, but i have now no power at bottom heater and upper heater.

Now i think there is a blue relay broken to. So i want to change them.

QIANJI JQC-3F(TT3)-12VDC
7A 250VAC | 10A 125VAC
12A 120VAC | 10A 28VDC

I want a replacement relays but i can't find the same relays in europe. Who knowns which relays i can use instead these ones?
BGA_netherlands
VIP Member
VIP Member
 
Posts: 175
Joined: Wed Oct 08, 2014 10:33 am
Location: Netherlands
National Flag:
Netherlands
Has thanked: 11 times
Been thanked: 10 times
Set up: 2x Seamark R5830 - Ecocell oven - 2x JBC CD-2 - Honton Hotplate - BOFA filter

Re: Scotle IR 360 pro V3 Bottom IR heaters don't turn on..

Postby BGA_netherlands » Sun May 31, 2015 6:21 pm

Finally my IR 360 is working again! Had serveral problems with it. 1 SSR was broken and a bad relay.

Have replaced SSR's with new ones and used new termalpaste. And replaced all relays. Parts are cheap so i did replaced all of them to eliminate problems in the future!
BGA_netherlands
VIP Member
VIP Member
 
Posts: 175
Joined: Wed Oct 08, 2014 10:33 am
Location: Netherlands
National Flag:
Netherlands
Has thanked: 11 times
Been thanked: 10 times
Set up: 2x Seamark R5830 - Ecocell oven - 2x JBC CD-2 - Honton Hotplate - BOFA filter

Re: Scotle IR 360 pro V3 Bottom IR heaters don't turn on..

Postby koubik » Sun May 31, 2015 6:26 pm

Glad to hear that everything is ok :roll:
User avatar
koubik
VIP Member
VIP Member
 
Posts: 286
Joined: Tue Dec 17, 2013 6:13 pm
Location: Greece
National Flag:
Greece
Has thanked: 15 times
Been thanked: 84 times
Set up: Scotle IR360 PRO V3

Previous

Return to Scotle

Who is online

Users browsing this forum: No registered users and 1 guest